Author Topic: Squib in 1911  (Read 2202 times)

August West

  • Full Member
  • ***
  • Posts: 165
Squib in 1911
« on: August 02, 2015, 10:46:40 AM »
With no cylinder gap, that 1911 is sure quiet when a squib occurs.  Had the headphones on -- and turned up -- but the squibb didn't sound much louder than a normal hammer fall.  Glad the shooter stopped on his own -- I sure wasn't any help in the situation as the R/O.

Shooter said he was using magnum primers.  But, the ball didn't get very far down the barrel.

Be careful out there (though, it's me that needs that advice).

Rafe

  • Newbie
  • *
  • Posts: 6
Re: Squib in 1911
« Reply #1 on: August 02, 2015, 05:16:22 PM »
Just glad I didn't pull the trigger! the lack of recoil was the only thing that keyed me!  ;D
Rafe
God created the whiskey to keep the Irish from ruling the world

Goody

  • Full Member
  • ***
  • Posts: 187
Re: Squib in 1911
« Reply #2 on: August 03, 2015, 11:09:11 AM »
Did the gun cycle with a squib???

Garrison Joe

  • Hero Member
  • *****
  • Posts: 764
Re: Squib in 1911
« Reply #3 on: August 03, 2015, 12:03:10 PM »
I've seen bunches of squibs in a 1911.  NEVER has the slide cycled.   

Tip of the week - if you yank the slide back and an empty case pops out, you had a squib, not a failure to feed a round.  :D  Check that barrel! 

Good luck, GJ
Good luck, GJ

Ride hard, shoot straight and speak the truth.    Col. J Cooper
Why else would you want to be here?

60708 Life/Regulator

Rafe

  • Newbie
  • *
  • Posts: 6
Re: Squib in 1911
« Reply #4 on: August 05, 2015, 06:36:30 PM »
It was a new pistol and I was having all kinds of trouble with it! plus I was reloading my own ammo with a new press, the gun shoots great but ammo issues with the new press and lack of break-in etc.. lead to my issue, I think the gun cycled  partially, not sure I have never had a squib before! for my cowboy guns I load nothing but black so kind of hard to get a squib. with this new fad of smokeless I gotta be extra carful! just glad no one got hurt.
Rafe
God created the whiskey to keep the Irish from ruling the world

Nawlins Kid

  • WBAS Committee & Ambassadors
  • Full Member
  • *******
  • Posts: 155
Re: Squib in 1911
« Reply #5 on: August 06, 2015, 05:03:05 AM »
About three years ago we had a WB mini match at our cowboy annual .I was the T/O as the shooter was firing his pistol and it must have been the third round being fired that didn't sound right. Before I could say anything the shooter shot the next round and bang the pistol locked up.  When he finally got the pistol apart  ( which by the way it was being shot for the first time) the barrel had a horizontal crack about 1 1/2 in. long closer to the bushing end. There was nothing in the barrel. The question is it possible  that a squib that stops at the end of the barrel  allow the pistol to feed the next round and to fire? Is it also possible that the barrel could have had a defect?  I would say it was less than 25 rounds that were shot before the stopage.

Nawlins[/size]
« Last Edit: August 06, 2015, 07:26:40 AM by Nawlins Kid »

Garrison Joe

  • Hero Member
  • *****
  • Posts: 764
Re: Squib in 1911
« Reply #6 on: August 06, 2015, 06:04:49 AM »
About three years ago we had a WB mini match at our cowboy annual .I was the T/O as the shooter was firing his pistol and it must have been the third round being fired that didn't sound right. Before I could say anything the shooter shot the next round and bang the pistol locked up.  When he finally got the pistol apart  ( which by the way it was being shot for the first time) the barrel had a horizontal crack about 1 1/2 in. long closer to the bushing end. There was nothing in the barrel. The question is it possible  that a squib that stops at the end of the barrel  allow the pistol to feed the next round and to fire? Is it also possible that the barrel could have had a defect?  I would say it was less than 25 rounds that were shot before the stoppage.

Nawlins

Almost certainly that was caused by a squib that, as you surmised, stuck the bullet most of the way into the barrel.   Mag primers or a slug that is groove diameter or slightly under sized makes this more likely.  1911 barrels are pretty thin out by the muzzle.   

Overpressure (excessive loads) in 1911's more often splits open the chamber (have seen a couple of shooters do that, too).  But a stuck slug - bulges or splits the barrel closer to where the squibbed slug stuck.
   
Stopping a shooter who has just encountered a squib in the 1911 is VITALLY important to prevent gun damage. 

I believe more TO's need to be thinking "call the squib if there is one" right before they touch the timer button.  The infrequent squibs (seems I save my year's allotment so they appear at EOT) that I get, I call on myself, rather than the TO yelling it out.

Good luck, GJ
« Last Edit: August 06, 2015, 09:25:51 AM by Garrison Joe »
Good luck, GJ

Ride hard, shoot straight and speak the truth.    Col. J Cooper
Why else would you want to be here?

60708 Life/Regulator